THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
1
THUNDER LASER
SYSTEMS
User’s manual for NOVA-35 www.thunderlaser.com
[emailprotected]
December 31, 2015
Original Instruction
http://www.thunderlaser.com/mailto:[emailprotected]
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
2
Introduction This manual has been designated as the thunderlaser systems, laser cutting
machine installation and user guide;The manual is divided intofive chapters,
Including general information instructions, safety instructions,the key
components of every laser cutting systems and the installationsteps, operation
instructions and maintenance instructions from THUNDERLASERCompany.
Frist, it should be emphasized that the installation of eachsystem must meet
the requirements, and make it consistent with the installationrequirements of
THUNDERLASER. If not, the machine will not working properly,poorperformance,
life shortened,maintenance costs increased and even machinedamage .
The note is for getting a specific requirement of systeminstallation,and we
hope every customer try to understand these notes beforeinstallation and usage,
thus you can correctly install and use. If you meet anyinstallation problems,
you can contact our technical staff and customer servicestaff.(At the same time,
you can also refer to the machine installation video that weposted on youtube.
The specific URL is
http://www.thunderlaser.com/how-to-use-your-laser-machine Or
https://www.youtube.com/watch?v=NpLo1L0NQx8&list=PLjSZrgjcrhs7QucNN-3jx7rZapDGfj
G-5 .)
http://www.thunderlaser.com/how-to-use-your-laser-machinehttps://www.youtube.com/watch?v=NpLo1L0NQx8&list=PLjSZrgjcrhs7QucNN-3jx7rZapDGfjG-5https://www.youtube.com/watch?v=NpLo1L0NQx8&list=PLjSZrgjcrhs7QucNN-3jx7rZapDGfjG-5
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
3
Contents
Chapter1 General....................................................................................................................................5
1.1 General Information.......................................................................................................................5
1.2 Designated......................................................................................................................................6
1.3 Disposal remarks............................................................................................................................6
1.4 Technical Data/Device Specification.............................................................................................7
1.5 Manufacturer’s Label.....................................................................................................................9
1.6 EC Declaration of Conformity.....................................................................................................10
Chapter 2 Safety....................................................................................................................................11
2.1 General Safety Information........................................................................................................11
2.2 Laser Safety Information............................................................................................................13
2.3 Safety Precautions When Operating the Device........................................................................14
2.4 Warning and Information Labels..................................................................................................15
Chapter 3 Process of Installing..........................................................................................................17
3.1 Unpacking.....................................................................................................................................17
3.2 Location..........................................................................................................................................18
3.3 Before Installaion.........................................................................................................................19
3.4 Exhaust System - Requirements.....................................................................................................21
3.5 Air System -Requirements.............................................................................................................21
3.6 Computer - Requirements..............................................................................................................22
3.7 Connections....................................................................................................................................23
3.7.1 Connecting the Mains............................................................................................................23
3.7.2 Connecting the Computer......................................................................................................24
3.7.3 Connecting the Exhaust System............................................................................................25
3.7.4 Connecting the Air System....................................................................................................27
3.7.5 Connecting the Cooling System............................................................................................28
Chapter 4 Operation...........................................................................................................................29
4.1 Machine View...............................................................................................................................29
4.2 ON/OFF Switch............................................................................................................................34
4.3 How to use the TL-Timer.............................................................................................................35
4.4 How to replace the 4 inch laser head and HR laser head.............................................................37
4.5 How to adjust focus distance using manual/auto.........................................................................39
4.6 How to Use the Display................................................................................................................42
4.6.1 Function of the Buttons.........................................................................................................42
4.6.2 The Main Interface................................................................................................................44
4.6.3 Speed Key..............................................................................................................................45
4.6.4 Max/Min Power Keys...........................................................................................................45
4.6.5 Set the Layer Parameters.......................................................................................................46
4.6.6 Z/U Key.................................................................................................................................46
4.6.7 Z Move..................................................................................................................................47
4.6.8 U Move..................................................................................................................................47
4.6.9 Axis Reset+............................................................................................................................47
4.6.10 ManualSet+.........................................................................................................................48
4.6.11 Laser Set+............................................................................................................................48
4.6.12 Origin Set.............................................................................................................................49
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
4
4.6.13 Set Fact Parameters.............................................................................................................50
4.6.14 Def. Fact Parameters...........................................................................................................50
4.6.15 Auto Focus...........................................................................................................................50
4.6.16 Language.............................................................................................................................50
4.6.17 IP Setup................................................................................................................................51
4.6.18Diagnoses.............................................................................................................................51
4.6.19 Screen Origin.......................................................................................................................52
4.6.20 File Key...............................................................................................................................53
4.6.21 Alarm Information of Display.............................................................................................55
4.7 The First Time Running the Laser................................................................................................56
4.8 Workstation Area Indication...........................................................................................................58
4.9 Rotary Engraving Attachment......................................................................................................59
4.10 For Laser Engraving...................................................................................................................62
Chapter 5 Maintenance......................................................................................................................63
5.1 Cleaning the Laser Machine.........................................................................................................63
5.2 Cleaning the Optical Parts............................................................................................................64
5.2.1 Cleaning the Focus Lens.......................................................................................................64
5.2.2 Cleaning the Mirrors...........................................................................................................66
5.2.3 Cleaning Beam Combiner.....................................................................................................68
5.3 Maintain the X/Y/Z Rails.............................................................................................................69
5.4 Check the Beam Path....................................................................................................................70
5.5 Change Cooling Water for The Water Chiller................................................................................71
5.6 Maintenance Plan.........................................................................................................................72
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
5
Chapter1 General
1.1 General Information
Caution:
Please read and follow this Operation Manual carefully, beforeinstallation
and operation. Damage to persons and/or material can result fromnot following
individual points of the Operation Manual!
Operation of the system is only permitted with equipment andspare parts
supplied or listed in the spare parts and consumables lists.
Auxiliary equipment must be adjusted to the base machine (anyqueries to
dealer or manufacturer).
The following symbols are used for easier understanding of theOperation Manual:
Caution: This component is under voltage. In these areasstrictly
observe the safety instructions regarding electricity. Care isto be taken
in particular during maintenance and repair work.
Caution: In this area pay attention to the possible dangers ofthe laser
beam.
Caution: Warning of hand injury
Caution: Indicates the potential for fire danger when operationthe
laser. Do operate the laser machine when unattended
Tips: Note or information on individual components of the devicethat
simplify the use or make it more understandable.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
6
1.2 Designated
The THUNDER LASER NOVA-35 is used for engraving and cutting ofsigns, stamps and suchlike.
A wide variety of materials such as rubber, acrylic, coatedmetal, tin, special steel,
anodized aluminum, cork, cardboard, glass, leather, marble,several plastics and wood
can be processed on the laser.
1. The engraving process must only be performed with a perfectlyadjusted machine.
2. For cutting applications with 80 W the use of the cuttingtable is absolutely necessary.
3. Use of the system in other areas is against the designateduse. The manufacturer does
not admit liability for damage to personal and/or equipmentresulting from such use.
4, The system must only be operated, maintained and repaired, bypersonnel that are
familiar with the designated field of use and the dangers of themachine!
5. Non-observance of the instructions for operation, maintenanceand repair described in
this Operation Manual excludes any liability of the manufacturerif a defect occurs.
6. Caution when processing conductive materials (carbon fibers),Conductive dust or
particles in the ambient air might damage electrical componentsand lead to short circuits.
Bear in mind that those defects are not warranted.
1.3 Disposal remarks
Do not dispose the machine with domestic waste!
Electronic devices have to be disposed according to the regionaldirectives on electronic
and electric waste disposal. In case of further questions,please ask your supplier. He
might take care of proper disposal.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
7
1.4 Technical Data / Device Specification
Mechanics
Working area 35.4“x 23.6“/ 900 x 600 mm
Table Size 39.4“x 28.7“/ 1000 x 730 mm
Z Axis Height 9.1 inch / 230 mm
Max. Height of work piece (Motorized Table, Standard laser head)9.1 inch / 230 mm
Max. Height of work piece (No Motorize Table, Standard Laserhead) 1-2.1 inch /27- 55mm
Max. Engraving speed 39 inch/sec. / 1000 mm/sec. Standard
Cutting speed depending on material, thickness, laser power
Motor Easy Servo Motor
Drive Hybrid Servo Drive
Work piece table Solid metal (Honey comb table)
Max. load of work piece table 30 kg
Net Weight 230kgs (507Ibs)
Lenses available (focal distance) 2, 0”
Focus lens diameter 20mm
Reflector diameter 25mm
Beam combiner diameter 25mm
Dimensions
W x D x H 59.1“x 43.5“x 40.9“/ 1500 x 1105 mm x 1040 mm
Max Part Size (W x L x H)
Front Door Closed 39.4“x 28.7“x 10.6“/ 1000 x 730 mm x 230mm
Pass-Through Door 39.4“ x∞“x 1.2“/ 1000 x∞mm x 20 mm
Features
Standard:
Red Dot Pointer, Auto Focus, Motorized Table, Pass-Through Door,Air Assist, Water
Pump, Exhaust Fan, Honey Comb Table, 2,0”(50.8mm)Focus Lens,Easily Adjustable
Home Position, LCD Display, 3D Engraving, “No Water “protection,Emergency Stop,
Maintenance mode, Open cover protection, TL-Timer, The warninglight.
Optional:
Rotary Attachment, Water Chiller Attachment, High Resolutionhead (up to 1000DPI, while
standard laser head Max is 500DPI), High air compressor set(Includes water filter).
Control System
Laser power Adjustable from 2 - 95% (typically 12-95%)
Interface Hardware USB: connect to PC and U-disk
Ethernet: connect to PC
Interface Software RDWorksV8
Operating Modes Optimized raster, vector, and combined mode
Buffer Memory 128 MB Standards
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
8
Laser Equipment
Laser Type Sealed CO2 Glass Laser Tube
Laser Power: 80W,100W, 130W
Wavelength 10, 6µm
Red dot pointer Laser Power< 5mW
Wavelength 630nm – 680nm
Cooling System
Air Cooling System Air-Cooled
Water Cooling System Water Cooled
Electricity, Power, Fuse
Electricity Requirement 110 to 240 volts, 50 or 60 Hz, Singlephase
Power consumption 1400W (Assembly 80Watt Laser Tube)
1500W (Assembly 100Watt Laser Tube)
1700W (Assembly 130Watt Laser Tube)
Recommended fuse 15A, 230V (80W/100W Laser Tube)
20A, 115V (80W/100W Laser Tube) and 20A, 230V (130W LaserTube)
25A, 115V (130W Laser Tube)
Ambient Conditions
Ambient temperature +15°C to +35°C / 59°F to 95°F
Humidity 40% to max. 70%, not condensing
Laser Safety
Laser class CDRH Laser Safety
Laser Class 1(H)
CE compliant FDA approved
Interlock Double interlock safety system
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
9
1.5 Manufacturer's Label
The manufacturer's label is located on the back of the device(see Figure below).
It is recommended to enter data such as serial number and yearof manufacture into the
Manufacturer label below so that you always have this data handyif you have problems
with your device or require spare parts.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
10
1.6 EC Declaration of Conformity
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
11
Chapter 2 Safety
2.1 General Safety Information
All personnel involved in installation, set-up, operationmaintenance and repair of the
machine, must have read and understood the Operation Manual andin particular the
"Safety" section. The user is recommended to generatecompany-internal instructions
considering the professional qualifications of the personnelemployed in each case, and
the receipt of the instruction/Operation Manual or theparticipation at introduction/training
should be acknowledged in writing in each case.
Safety-conscious of Working
The machine must only be operated by trained and authorizedpersonnel.
The scopes of competence for the different activities in thescope of operating the
machine must be clearly defined and observed, so that under theaspect of safety no
unclear questions of competence occur. This applies inparticular to activities on the
electric equipment, which must only be performed by specialexperts.
For all activities concerning installation, set-up, start-up,operation, modifications of
conditions and methods of operation, maintenance, inspection andrepair, the switch-off
procedures that may be provided in the Operation Manual must beobserved.
Safety Information for the User and/or Operating Personnel
1. No working methods are permitted that affect the safety ofthe machine.
2. The operator must also ensure that no unauthorized personswork with the machine
(e.g. by activating equipment without authorization).
3. It is the duty of the operator, to check the machine beforestart of work for externally
visible damage and defects, and to immediately report changesthat appear (including
behavior during operation) that affect the safety.
4. The user must provide that the machine is only operated inperfect condition.
5. The user must guarantee the cleanness and accessibility atand around the machine
by corresponding instructions and controls.
6. Principally, no safety components may be removed or disabled(already here we
emphasize the imminent dangers, for example severe burns, lossof eye-sight). If the
removal of safety components is required during repair andservice, the replacement
of the safety components must be performed immediately aftercompletion of the
service and repair activities.
7. Preparation, retooling, change of work piece, maintenance andrepair activities must
only performed with equipment switched off, by trainedpersonnel.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
12
8. It is forbidden to perform unauthorized modifications andchanges to the machine. It is
emphasized, that any unauthorized modifications to the machineare not permitted for
safety reasons.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
13
2.2 Laser Safety Information
1. To assess the potential dangers laser systems pose, they areclassified into
4 safety classes, thunder laser NOVA-35 is a device of class 1.This is guaranteed by the
protective housing and the safety installations.
Please note that improper and warranty operation of the devicecan override the status of
Safety class 1 and can cause the emission of harmfulradiation.
2. This laser engraving system contains a carbon dioxide (CO2)laser of class 4
that emits intensive and invisible laser radiation. Withoutsafety precautions
the direct radiation or even diffuse reflected radiation isdangerous!
3. Without safety precautions, the following risks exist withexposure to laser radiation:
Eyes: Burns to the cornea
Skin: Burns
Clothing: Danger of fire
4. Never try to modify or disassemble the laser and do not tryto start up a system that had
been modified or disassembled!
5. Dangerous radiation exposure can result from the use ofoperation or adjustment
equipment other than that described here, and if differentoperational methods are
performed.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
14
2.3 Safety Precautions when Operating the Device
In your thunder laser NOVA-35, a closed safety system isintegrated which immediately
switches off the power to the laser tube and all axis driverswhen the protection cover is
opened. Consequently an incomplete engraving can occur if thecover is opened during
operation. Therefore, first press the "PAUSE" button, if youwant to interrupt an engraving
process.
Please remember the following safety precautions when workingwith this device:
CO2 Fire extinguishers should be placed near laser
Do not store any flammable materials in the inside of thedevice. Particularly leftovers of
produced materials have to be removed to prevent firehazard.
Please maintain Free air-flow surrounding this system. At alltimes, do not cover during
operation.
These lasers emit invisible radiation; safety glasses should beworn when maintenance
these machines for your protection.
Do not disable limit switches or safety features as this caninvalidate warranties and cause
damage to you and the machine.
Do not leave the laser unattended when it is working, smallscraps can ignite and without
supervision can destroy the machine if not checked.
Adjustment of the beam path must be performed only by especiallytrained personnel. An
improper setting can lead to uncontrolled emission of the laserradiation.
Before processing materials the user must verify, whetherharmful materials can be
generated and whether the filter equipment of the exhaust systemis suitable for the
harmful materials. We emphasize that it is the responsibility ofthe user, to consider the
national and regional threshold values for dust, fogs and gaseswhen selecting the filters
and the exhaust system. (The values for the maximum workplaceconcentration must not
be exceeded.)
PVC (polyvinyl chloride) must under no circ*mstances beprocessed with the laser.
Should you have further questions before starting work, pleasefeel free to write us
an email at: [emailprotected]
mailto:[emailprotected]
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
15
2.4 Warning and Information Labels
The warning and information labels are attached in suchpositions of the device that could
represent a source of danger during set-up and operation.Therefore, follow the
information on the labels. If labels are lost or damaged, theymust be replaced
immediately.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
16
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
17
Chapter 3 Process of Installing
3.1 Unpacking
You receive your THUNDER LASER NOVA-35 packed in a wooden box,which contains
the laser machine and additional accessories. The followingsteps give you an overview of
the unpacking and assembly of the laser. Please follow thesesteps carefully.
Tips: Keep the packing box. You will require it in case of areturn.
Dispose all waste according to the applicable waste disposallaw.
1. Put the wooden box on a flat and spacious room forunpacking.
2. Remove the machine box; carefully remove the foam material,which protects the
viewing window of the cover and around the machine.
3. Take out the key,open the door of the laser,Remove theaccessories box which
contains all accessory parts required for the installation ofthe laser machine.
And check if there’s anything damaged or missed duringshipping.
4. You will see an attachment table on the machine; please checkwhether the
accessories are all on the table.
5. Please keep the keys and the warranty certificate well (andplease show us your
warranty certificate if you need tech support for the machinefailure, then we will provide
you the best technical service).
6. Remove the sponge and nylon cable ties from inside themachine, and then start to
install the machine (below chapters are installationdetails)
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
18
3.2 Location
Before you install the laser system, you should select anappropriate location. Follow the
guidelines shown below:
1. Avoid locations where the system is exposed to hightemperatures, dust and high
humidity. (The humidity must not exceed 70% and the temperaturemust not be close
to the dew point.)
2. Avoid locations, where the system is exposed to mechanicalshocks.
1. Fuse protection:
Do not connect other devices via the laser fuse, as the lasersystem requires the full
amperage.
Tips:
1. Avoid locations with poor air circulation; select a locationclose to ventilation (if
available).
2. Select a location, whose room temperature is between 15 °Cand 25 °C (59° – 77° F).
This is fundamental to maintain consistent and reliableoperation of a CO2 laser, Metal
RF or Glass tube and the machine itself.
Avoid higher ambient temperatures and strong exposure of theengraver to the sun.
Use blinds, if required.
3. Mechanical shock and vibration of the laser will havedetrimental effects on the
performance and life expectancy of the machine. It will manifest(over a period of time)
with a noticeable decrease in performance and increasedmaintenance required,
possibly even damage. Setting your Thunder Laser up in ssuitable temperature
controlled, dust free, moisture free, level, stable surface (alevel concrete floor) with
the recommended extraction is critical to the ongoingperformance of the machine. It
is also a warranty condition.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
19
3.3 Before Installation
1. Take out the sponge around the laser tube. Like below:
2. Take out the nylon cable ties around the honey comb plate andX axis.
Remove the transparent bag out of the first mirror mounts, thesecond mirror
mounts, the third mirror mounts and the standard laser head.Like below:
PS: The lid with a set of key and a manual focusing tool forusers
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
20
3. Open the emergency switch (must do it for the first time touse the machine).
Like below
4. After carried the machine into room, please re-fix the footof the four corners.
Please refer to below shown:
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
21
3.4 Exhaust System – Requirements
To guarantee the right ventilation during the engraving and thecutting. The device must
be equipped with a fine exhaust fan(generation of rubber dust),if you use an carbon filter
(neutralization of smells) will be better for exhaust effect. Agood exhaust fan of the
outgoing air is also required when cutting plastics or engravingwood.
Connection - see section 3.7.3 connecting the ExhaustSystem.
Do not start the machine without an adequate exhaust system.
3.5 Air System – Requirements
To guarantee do not catch file and too much smoke during theengraving and the cutting.
The device must be connecting with the laser to make sure thelaser is safe during the
work.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
22
3.6 Computer – Requirements
The following recommendation represents the minimumrequirements. When using a
more powerful computer the graphics are generated and displayedfaster and the
computing times and the data transfer to the laser are reduced.To use the newest
software version, you might have to abide otherrequirements.
• Windows 10 (32 bit or 64 bit )
• Windows 8 (32 bit or 64 bit )
• Windows 7 (32 bit or 64 bit )
Windows Vista (with Service Pack 1 or later)
Windows XP (with Service Pack 2 or later)
• 1024 MB of RAM, 400 MB of hard disk space
• Pentium® 3 or 4 processor or AMD Athlon™ XP
• 1024 x 768 or better monitor resolution
• 1 free USB interface
• 1 free Ethernet interface
• Mouse
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
23
3.7 Connections
Perform the connections exactly in the order described;otherwise electrostatic charging
can damage your computer and/or the electronics of the lasersystem.
3.7.1 Connecting the Mains
Connect one end of the mains cable with the connection socket atthe rear side of the
laser device (see Figure below) and the other end with aprotected power outlet.
Mains voltage and operating voltage must correspond (AC 230V50/60 Hz or AC 115V
50/60 Hz) – see information label beside the connectionsocket.
The machine (certain) Power Cable for each country was putinside the Tool box with
machine.
Under no circ*mstances switch on the device if the voltages donot correspond.
Tips: The main fuses are located inside the connection socketand are accessible from
the exterior.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
24
3.7.2 Connecting the Computer
Connecting the Computer and the machine by using the USB cable.Like below:
Connecting the Computer and the machine by using the Ethernetcable. Like below:
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
25
3.7.3 Connecting the Exhaust System
How to set up the exhaust system
Insert one side of the gray exhaust pipe into the fan inlet andthe other side into the
fuselage behind the exhaust tank. Insert one side of the grayexhaust pipe into the fan
outlet and put the other side of the pipe outside where you work(If the machine is far from
the outside of the room that the gas manufactured by the machinecannot be discharged;
then you might need an dust/fume filter, it can keep the airquality of your working
environment well).
Please refer to the following pictures about how to install theexhaust pipe:
Also you can refer to the video on how to set up your MARS lasermachine in our website
http://www.thunderlaser.com/video/laser-machine/setup-your-mars-laser-machine.html
The input voltage must correspond (AC 230V 50/60 Hz or AC 115V50/60 Hz) – see
information label beside the connection socket.
http://www.thunderlaser.com/video/laser-machine/setup-your-mars-laser-machine.html
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
26
Tips: Do not connect the air compressor or the water chiller tothe above interface,if
connect them to the above interfaces that cause in failure ofthe machine, the warranty
does not covered.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
27
3.7.4 Connecting the Air System
First of all, Install a air blowing mouth (copper) to the airsystem, then connect the hoses
(white side) to the mouth, the other side to the machine. Afterthat, please connect the
power cable (of the air system) to the machine. Like below:
The input voltage must correspond (AC 230V 50/60 Hz or AC 115V50/60 Hz) – see
information label beside the connection socket.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
28
3.7.5 Connecting the Cooling System
If you have the water chiller, and please connect to the waterchiller priority. If not, and
please connect to the water pump.
The connection of the machine and the Water chiller.
① Take out one of the water pipes and connect to the waterchiller where marked as
“OUTLET”, the other side of the pipe connect to the machinewhere marked as
“Water IN”.
② The other pipe, please connect to “INLET” of water chiller and“Water OUT” of
machine.
③ Just refer to below picture shown that the order from 1 to 4port to connect them.
For example: 1 to 1, 2 to 2
We will provide a certain chiller power cable for differentcountries, and the power cable
will be put inside a box together with the water chiller.
The connection of the machine and the Water pump
① Take out one of the water pipes and connect to the waterpump,the other side
connect to the machine where marked as “Water IN”.
② The other pipe, please connect to the machine where marked as“Water OUT”.,
the other side directly into the water.
Like below:
We will provide a certain pump power cable for differentcountries, and the power cable
has been connected to the pump already before we send itout.
Get through the water chiller or the water pump, and turn on themain power.
Check the water chiller or pump to work(If normally work, thegreen light will light or water
will flow from the pipe).
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
29
Chapter 4 Operation
4.1 Machine View
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
30
1. Top lid 17. LED lamp
2. Blow air conditioner 18. Laser power switch
3. Auto focus sensor 19. Main power switch
4. Left-up side door 20. Ethernet port
5. Left side door 21. U-disk connection port(USB)
6. X-axis 22. PC connection port(USB)
7. Dual laser heads 23. Right side door
8. Front door 24. Right-up side door
9. Honey comb table 25. Indicate light
10. Y-axis 26. Power supply socket
11. Front up door 27. Laser tube cover
12. Flap protection sensor 28. Exhaust hose
13. Control panel 29. Blow air port
14. HOLD-TO-RUN button 30. Water in and water out
15. Emergency stop switch 31. Rear door
16. Mode selection switch 32. Manufacturer’s label
1. Top lid
If the Top lid is opened, no data is processed. When theprotection cover is opened
during working, the motion system is stopped and the lasersource is turned off.
During processing of commands the protection cover must only beopened after
pressing the “Pause “button.
2. Blow air conditioner
It’s used for adjust that blow air amount.
3. Auto focus sensor
Used for the automatic focusing of the work table.
4. Left-up side door
Open this door for cleaning the second reflective mirror oralign that laser beam
5. Left side door
There is laser power supplier, Ammeter, TL-Timer etc. pleaseopen this door for
checking these parts, but must pay attention to the electriccurrent.
6. X-axis
The motion system is that performs the mechanical movements in Xdirection. The
X-axis is visible in the working area.
7. Laser head
Laser beam and red dot pointer are all come out from the laserhead, and the Auto
Focus switch is installed on the laser head, too. The bottom oflaser head is parallel to
the bottom of the autofocus switch.
8. Front door
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
31
Open this door for cleaning the waste after working.
This door is locked by using two outside locks.
9. Honey comb table
The honey comb plate to be processed is put onto the workingtable. Put the material
on the working table for engraving & cutting
10. Y-axis
The motion system is that performs the mechanical movements in Ydirection. The
Y-axis is visible in the working area.
11. Front up door
Open this door for take out the honey comb table and it’sconvenient to put that
material on working table
This door is locked by using inside screws and outsidelocks.
12. Flap protection sensor
This is where Open flat protection exist. Laser will stopworking once the cover is
opened during working.
13. Control panel
You can control the X-axis, Y-axis and Z-axis manually by thedisplay panel, it also
shows the working time, power, speed and the whole working timeand affords many
function options(please view this chapter 4.3 for detail).
14. HOLD TO RUN button
When the user turn mode switch to manual mode, the laser powerwill keeping on
when you open or close the cover or lid, but the motion systempower will still off, and
hold pressed the HOLD TO RUN button to provide the power formotion system
15. Emergency stop switch
Once there’s an accident happen (laser catch fire, laser outleakage) during working,
please press down E-stop switch immediately. It will be cut offthe laser power and the
motion power immediately.
16. Mode selection switch
It is used for switch that laser machine to normal mode orwarranty mode
When the user does switching it to auto mode, the laser &motion system power will
be cut off when open the cover or lid.
When the user switching it to manual mode, the laser power willkeeping power on
when opens the cover or lid, keeping push the next blackbutton(hold to run) to let the
motion system gets the power and works
17. LED lamp
It’s used for lighting the working table once turn the Mainswitch on.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
32
18. Laser power switch
The laser power will be on while you turn it on
19. Main power switch
The laser machine will be start while you turn it on
20. Ethernet port
This Ethernet port is for connecting computer.
21. U-disk connection port(USB)
You can save the file as a U-disk File by press “SaveToUFile” onthe software, then
save it to the u-disk and insert the u-disk to the port of lasermachine, then use the
control panel to select and control it to work
22. PC connection port(USB)
This USB is for connecting computer.
23. Right side door
There are laser controller, driver(Hybrid Servo Drive and MicroStepper Drive ),
power supplier (both 24v DC and 36vDC), the main connectingcables and cooling fan
here, please open this door for checking these parts, but mustpay attention to the
electric current. if you need to repair, please contact withprofessional maintenance
staff.
24. Right-up side door
Maintenance for the Emergency stop button if required
This door is locked by using outside locks.
25. Indicate light
The indicate light is always keeping green color while the laserdoes not work or
working but the lid is closed.
The indicate light will turn red color while you switching themode button to manual
mode
The indicate light will turn yellow color while the lid/cover isopened during working.
26. Laser supply socket
To connect the main power and the extend power according thelabel information. And
in the main power socket have the fuses.
27. Laser tube cover
There are installed the laser tube, red dot pointer device, beamcombiner and the first
reflective mirror mount.
28. Exhaust hose
This is for installing the exhaust device.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
33
29. Blow air port
This port is for connecting hoses of the air compressor.
30. Water in and water out
Both ports are for connection with water pump or waterchiller.
31. Rear door
There are installed cables banks etc. please open this door forchecking these parts,
but must pay attention to that electric current.
32. Manufacture’s Label
It’s Show you the laser information like serial number ormanufacturing date etc.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
34
4.2 ON/OFF Switch
The mains and the laser supply power ON/OFF switch
The following conditions must be fulfilled for correct startup:
Unrestricted freedom of motion of the mechanics
No materials under the engraving table
Protection covers closed
When turn on the power of machine, and note that turn on themain switch first and then
the laser supply power switch
If all covers are closed, immediately after being switched on,the device starts the
referencing process. When the referencing process is completedcorrectly, an acoustic
signal sounds and the device is ready for operation. Theoperation panel will display the
home screen when the laser is completed resets.
Before switching on the device, the user must make sure that noobjects
of any kind are located inside the operating space, which couldlimit or obstruct the
mechanics of the device.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
35
4.3 How to use the TL-Timer
The TL-Timer is an additional tool for laser machines.
It will control laser machines periphery like exhaust fan, airpump, warning lights,
pneumatic lifts, electrical locks and lost of other stuffautomatically.
This will increase the ease of use of your laser machine.
Please note the different types of connection, which makes theTL-Timer able to work with
each kind of laser controller.
Operation:
Normal use:
The TL-Timer gets activated by a work status signal from lasercontroller and an
open/close signal from the lid.
When the laser is working with the lid is closed, the second redLED and third red LED
lights up and 2 relays will be activated until the signal fromcontroller gets turned off.
Without control signal the 2 relays will stay turned on until agiven delay time has expired.
When the laser is working with the lid is opened, the first redLED light will be on and the
relay will be activated until you closed the lid.
Each relay has a freely adjustable delay time from 0-99seconds.
Set up delay time:
Enter “Set” switch once. The red LED will blink and the displaywill show you the delay
time in second for the first relay. A red LED close to theactive relay will show you. Which
one is active?
The display does show the delay time in seconds. By pressing“down” or “up” you can
change the value. By holding a switch down for more than 1second the value will
increase or decrease automatically.
By pressing “Set” you can switch to relay number 2 now andconfirm the delay time for this
one.
For changing delay values for 3rd
and 4rd
relay you have to press “Set” again.
When 4th relay is active and you press “Set” again, the TL-Timerwill turn back to normal
operating mode, the red LED will stop blinking, but the blue LEDwill be still keeping on
After turning of power the TL-Timer will remember thedelay-time-values, you did enter
before.
Relay-Output:
Each of the 4 relays offers an opening and closing switch withcurrent capacity of max.
8 Amps and a power capacity of max. 1000W.
Higher loads must be controlled by using a power contactor.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
36
About TL-Timer controller interface and buttons description:
1:Interface 1,connection with warning light ,delay time is setto 0 second(Factory default
settings, change it if required)
2:Interface 2,connection with air pump,delay time is set to 5second(Factory default
settings, change it if required)
3:Interface 3,connection with exhaust fan,delay time is set to15 second(Factory default
settings, change it if required)
4:Interface 4,spare interface,users can connect the relevantequipment if required
5:LED lights display,set the delay time for viewing eachinterface and enter
6:”UP” button to increase delay time
7:”DOWN” button to reduce delay time
8:”Set” button to confirm your setting
9:Interface 9,” lid state” interface
10:Interface 10, “Working state” interface
11: Interface 11, 5V DC voltage power interface
12: upgrade interface
13: auto and manual
Where the TL-Timer is installed with Thunder Laser machine,please refer to the pictures
as bellows:
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
37
4.4 How to replace the 4 inch and HR laser head
1)How to replace the 4 inch laser head
1. Move the table down till there’s enough space to take thestandard head out and
install the 4” laser head.
2. Separate the standard head mount, like below:
①separate the auto focus port ①take out the mount mouth
②loosen the screw
③take out the air hose
3. Install the 4” laser head like below:
①4” laser head ①reinstall the auto focus
②assemble the nozzle cone to the 4” head ②fix the laser head
③connect the air hose,
Tips: If there’s no Auto focus for your machine, then no need todeal with it.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
38
2)How to replace the HR laser head
1. Move the table down till there’s enough space to take thestandard head out and
install the HR head.
2. Separate the standard head mount, like aboveinstructions.
3. Install HR head, like below:
①fix the head
②connect the air hose.
Tips: Since HR head is sensitive for focus distance, it’ssuggested to adjust the
focus by manual rather than auto focus.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
39
4.5 How to adjust focus distance by manual or auto
1). If there’s no auto focus function for your machine orthere’s fault for your auto focus,
you can refer to below instructions about how to adjust focus bymanually:
1. for standard laser head:
find the 6mm Acrylic Focus Tool for help to adjust the focusdirectly like below:
①Working Table
②Material
③Focus Tool
If the focus tool is not the best one for your material, you canuse the focus ruler for help
like below:
①Working Table
②Material
③Focus Ruler
Please note that the limit line of the head, this limit lineindicates the max height of laser
head, and keep the limited line inside the laser head mount. Soas to protect the laser
head from crashing into the honey comb table while z-axis doesreset/auto focus
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
40
2. For HR laser head
Since HR head is very sensitive for focus distance, thus we’vetested and made a special
focus tool (with a best distance) for each HR head, likebelow:
①Working Table
②Material
③The Best Focus Distance
④Focus Tool
Please note that the limit line of the head, this limit lineindicates the max height of laser
head, and keep the limited line inside the laser head mount. Soas to protect the laser
head from crashing into the honey comb table while z-axis doesreset/auto focus
3. For 4’’ laser head
4” laser head is not so sensitive for focus distance; you canset the distance about
10mm with the help of focus ruler
①Working Table
②Material
③Focus Rule
PS: Please keep the 4’’ laser head to the max height of laserhead
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
41
2) If there’s Auto Focus function for your machine, you canadjust the focus by auto, 1. Reset Z-axis.(Z-axis will move upuntil touch the Auto focus switch(or the machinery
limit switch), here the coordinate: 0.0 ) please refer to Pic1.
2. Set a correct focus distance, please refer to pic 2
3. Select “Auto focus” on display panel, then the table willauto focus directly, please refer
to pic 3.
1
2
3
PS: please do not use “auto focus” function while laser head
is HR laser head or 4’’ laser head.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
42
4.6 How to use the display
4.6.1 Function of the Buttons
Arrow buttons: control the movement of the laser
head.(also can be used to change the parameters in the controlpanel)
Z/U button: The Z/U key can be pressed when the system is idleor the work
is finished. On pressing this key, it will show some entries inthe interface, each entry
includes some functions, Z axes move, U axes move, each axes togo home etc.
Reset button: reset the machine.
Laser button: single press to draw a dot, press and hold todrill a hole.
Speed button: Set the speed of the current running layer, or setthe
direction keys’ move speed.
Min-Power button: Set the min laser power of the current runninglayer.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
43
Max-Power button: Set the max laser power of the current runninglayer,
or set the power of “Laser” Key.
File button: The management of the memory and U disc files.
Start-Pause button: run/pause the current job.
Origin button: set the starting point for the laser head.
Frame button: To track by the current file’s frame.
Esc button: To stop work, or return to the last menu.
Enter button: confirm your selection.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
44
4.6.2 The main interface
When the system is powered on, the screen will show asbelow:
File:
Speed:
MaxPow:
01
300mm/s
30.0%/30.0%
X:
Y:
Z:
150.2
153.5
3000
mm
mm
mm
01 400 25.0
02 200 29.1
03 100 31.5
Idle 00.00. 00 Count: 99 X : 180. 5 mm Y : 235. 6 mm connect
Graph display area
Graph layer parameters
Running Status
Working Number
Running parameters
Net Status File dimension
Coordinate
Running progress bar
Graph Display Area: To display the whole file’s track, anddisplay the running
track.
Running parameters: To display the running file’s file number,speed, max power
etc.;
Coordinate: To display the current coordinate of X,Y and Zaxes
Graph layer parameters: To display the layers’ information ofthe current file,
such as max or min power, speed etc.. When system is idle,dblclick the layer,
then users can change the layer’s parameters and the changingwould be
saved.
Running Status: To display the current status of the machine,such as Idle, Run,
Pause, Finish, etc.;
Running Progress Bar: To display the progress bar of the currentrunning file;
Working Number: To accumulate the work number of the currentfile.
File Dimension: To display the dimension of the currentfile;
Net status: To display the connecting status of theEthernet.
When work is Idle or finished, all keys can be pushed, users canselect a file to run, set
some parameters, preview to a select file etc. But, when work isrunning or paused, some
keys don’t respond when they are pushed.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
45
4.6.3 Speed Key
Push the “Speed” key when the screen is on the main interface,it will show as below:
Speed: mm/s
Modified press Enter
300
Push the “X+/-“ Keys to move the cursor in the numeral area, andpush the “Y+/-” keys to
change the value, then push the “Enter” key to save the change,push the “Esc” key to
invalidate the change.
4.6.4 Max/Min Power Keys
Push the “Max Power” or the “Min Power” keys when the screen ison the main interface, it
will show as below:
%
Modified press Enter
%
MaxPower1:
MaxPower2:
30.0
30.0
Press Z/U move item
%
Modified press Enter
%
MinPower1:
MinPower2:
30.0
30.0
Press Z/U move item
When “Z/U” key is pushed, the green block can move up and downto denote the
changing item, then “Y+/-” keys and “X+/-” keys can be used tochange the value.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
46
4.6.5 Set the Layer Parameters
After selecting a file to preview on the main interface, usercan push “Enter” key to let the
cursor move to the first layer, then “Y+/-” Keys can be pushedto select the intent layer, on
that time, user can push “Enter” key to check the selectedlayer’s parameters, show as
below:
02 200 29.1
03 100 31.5
01 400 25.1
MaxPower1: %
Modified press Enter
30.0
MaxPower2:
Press Z/U move item
%30.0
Layer0:
MinPower1: %22.0
MinPower2: %30.0
Speed: mm/s400
User can push “Z/U” Keys to move the green block on the intentparameter, then he could
change the parameter if needed. “OK” to validate the change, and“Esc” to invalidate the
change.
4.6.6 Z/U Key
The Z/U key can be pressed when the system is idle or the workis finished. On pressing
this key, it will show some entries in the followinginterface:
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
47
U move
Axis reset+
Manual Set+
Laser Set+
Origin set+
Set Fact Para
Def Fact Para
Auto Focus
Language+
IP setup+
Diagnoses+
Screen Origin+
Z move
Press up and down arrow keys to move the green block to theanticipant item, and then
push the “Enter” key to display the sub menu.
4.6.7 Z Move
When the green block is on “Z Move” item, to move the Z-axistable up and down by press
left and right arrow keys, then press ESC to go back to normal x& Y axis control.
4.6.8 U Move
When the green block is on “U Move” item, to move the Z-axistable up and down by press
left and right arrow keys,
4.6.9 Axis Reset+
When the green block is on this item, push the “Enter” key toshow as below:
X axis reset
Y axis reset
Z axis reset
U axis reset
XY axis reset
Press up and down arrow keys to move the cursor to one of theentry, then push “Enter”
key to restart the selected axis, the screen will show someinformation when resetting.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
48
4.6.10 Manual Set+
When the green block is on this item, push the “Enter” key toshow as below:
manual: mm
Modified press Enter
300
Mode:
Press Z/U move item
continue
Push “Z/U” key to move the green block, and when the green blockis on the “Mode” item,
push “X+-“ keys to select the anticipant value, “Continue” or“Manual”. When “Continue”
item is selected, then the “Manual” item is not valid, on thattime, push the direction keys
to move the corresponding axes, and when the pushed key isloosed, then the
corresponding axes will finish moving. When the Mode item is“manual”, then pushing the
direction key one time, the corresponding axes will move a fixedlength, unless the scope
is overstepped.
4.6.11 Laser Set+
When the green block is on this item, push the “Enter” key toshow as below:
Laser Set: ms
Modified press Enter
50
Mode:
Press Z/U move item
continue
Push “Z/U” key to move the green block, and when the green blockis on the “Mode” item,
push “X+-“ keys to select the anticipant value, “Continue” or“Manual”. When “Continue”
item is selected, then the “Laser Set” item is not valid, onthat time, push the Laser key
to splash the enabled lasers, and when Laser key is loosed, thenthe lasers will finish
splashing. When the Mode item is “manual”, then pushing theLaser key one time, the
enabled lasers will splash a fixed time.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
49
4.6.12 Origin Set
When the green block is on this item, push the “Enter” key toshow as below:
Modified press Enter
Press Z/U move item
1
Origin enable1 Origin enable3
Origin enable2 Origin enable4
Set origin:
Next origin: 0
Muti origin enable
Push “Z/U” key to move the green block to the anticipant item,and when the green block
is on “enable” items, push “Enter” key to enable or disable theitem, when enabled, the
small diamonds is green, and when disabled, the small diamondsis grey. When the green
block is on the “Set origin” item or the “Next origin” item,push the “X+-“ keys to select the
value.
Pay attention to if when the green block is on the “Set origin”item, push the “X+-“ keys to
select a value, then, “Enter” key must be pushed to valid thechange, or, the change is
invalid.
Each item introduced as below:
Multiple Origins Enable: “Yes” or “No” can be selected. If youselect “No”, the
system will use the single-origin logic. You can press the“Origin” key and set the
origin, and only this origin can become valid. If you select“Yes”, the system will
use the multiple- origin logic and the “Origin” key on thekeyboard become invalid.
In such a case, the parameter of each origin must be set in themenu as follows.
Origin Enable1/2/3/4: after the multiple-origin logic isenabled, the four origins
can independently be prohibited and enabled.
Set Origin 1/2/3/4: after the multiple- origin logic is enabled,you can stop the
cursor at “Set as Origin 1/2/3/4”. Press the “Enter” key on thekeyboard and the
system will take the coordinate figures of current X/Y axles asthe corresponding
ones to the origin 1/2/3/4.
Next Origin: there are such five digits as 0~4 for option, whichare the origins to
be used for the next figure. Origin 0 means the origin set bythe “Origin” key on
the panel in the single- origin logic. 1~4 means the serialnumber of the origins in
the multiple- origin logic. Next origin can be modified to anyone of origin 1~4, so
as to control the start location of next work (the premise isthat the origin is
enabled), but it can’t be modified to origin 0.
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
50
Once the multiple- origin logic is selected and if the serialnumber of the
next origin is 1 and four origins are enabled, when the memoryfile function is
started or the processing file is uploaded into the PC and thisfile selects
“Take the Original Origin as current Origin”, the work startedfor each time will
use different origins. The rotation order of origin is1->2->3->4->1->2…….
4.6.13 Set Fact Parameters
After the “Set Fact Para” is selected and the Enter key pressed,the interface will show the
specific password to be entered when set as defaultparameter.
0 1 2 3 4 5 6 7 8 9
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z
123456
Password error
Password:
Push “X+/-” keys and “Y+/-” keys to select the characters, andpush the “Enter” key to
valid the characters, when finishing enter the password ,that isto say, the six characters, if
the password is error, it prompts there is some error, or, allparameters are stored.
After the manufacturer regulates all parameters of the machinewell
(including all manufacturer parameters and user parameters),this
function can be used to store the well-regulated parameters tohelp
users to recover the original parameters (including allmanufacturer
parameters and user parameters) through selecting “RecoverPara”
when they regulate parameters improperly.
4.6.14 Def. Fact Parameters
After the “Def Fact Para” is selected and the Enter key pressed,the “Successful Recovery”
dialog box will pop up to prompt that all manufacturerparameters and user parameters
are recovered successfully. You can return to the previous menuby press the Enter key.
4.6.15 Auto Focus
When the cursor stops at “Auto Focus”, press the Enter key tosearch for the focus(When
there is z axes, and the z axes reset function is enabled, theauto focusing is valid); press
the Esc key to return the prior menu.
4.6.16 Language
The item “Language” helps you to select a appropriate languewhich is displayed on the
pane:
Prompt
Prompt
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
51
Tradition
English
Simplify
4.6.17 IP Setup
When the green block is on this item, push the “Enter” key toshow as below:
IP address:
192
Gateway:
. . . 168 1 100
202 . . . 96 134 133
Modified press Enter
Press Z/U move item
Push “Z/U” key to move the changing item, then push “X+/-” keysand “Y+/-” keys to
change the value, when all the IP value and the Gateway valueare changed, push “Enter”
key to validate the change, or “Esc” key to invalidate thechange.
4.6.18 Diagnoses
If the “Diagnoses” item is pressed, the system will show asbelow:
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
52
X Limit+
Y Limit+
Z Limit+
U Limit+
Water prot1
Water prot2
Open prot
X Limit -
Y Limit-
Z Limit-
U Limit-
Read para
This interface shows some system input information, such aslimiter status, the status of
the water protecting, and the status of the foot switch etc..When the input is validated, the
color frame will be green, otherwise it’s gray.
4.6.19 Screen Origin
If the “Screen Origin” item is pressed, the system will show asbelow:
Top leftOrigin locat:
Modified press Enter
To modify pressß /à
There are four entries to be selected: Top Left, Top Right,Bottom Left and Bottom Right.
When one is selected, the previewed graph on the screen would beenantiomorphous
based on X or Y direction.
This item is only used to preview the file on the screen, and itis no
meaning to the machine’s movement.
Caution
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
53
4.6.20 File Key
1). Memory File
On the main interface, if “File” key is pressed, it will show asbelow:
File:
Speed:
MaxPow:
01
300mm/s
30.0%/30.0%
X:
Y:
Z:
150.2
153.5
3000
mm
mm
mm
01 400
02 200
03 100
File: Count:
Udisk+
Other+
Run
Track
Work time
Clear count
Delete
Copy to udisk
Read mem file
Idle 00.00.00 Count: 99 X: 180.5 mm Y: 235.6 mm connect
When showing this menu, the system would read the memory filefirstly, the file name and
the work times would be listed in the area, and the selectedfile is previewed in the bottom
right area. “Y+/-” keys could be used to move the cursor on thefile name list. When the
cursor is on a target file name, presses the “Enter” key, theselected file will be previewed
on the main interface, and then if “Esc” key is pushed, thepreview will disappear.
“X+/-” keys could be used to move the cursor left and right. Allthe item show as below:
Read mem file: read the memory file list;
Udisk: read the U disk file list;
Other: the other operation of the memory files;
Run: To run the selected file;
Track: To track the selected file, and the track mode isoptional;
Work time: To forecast the running time of the selected file,and the time is
accurate to 1ms;
Clear count: To clear the running times of the selectedfile;
Delete: To delete the selected file in the memory;
Copy to Udisk: To copy the selected file to Udisk;
If the “Other” entry is pressed, the system will show asbelow:
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
54
10Total:
delete all file
Clear all count
Current work time
Clear
Format drastically
Format speedly
Current work time: To forecast the running time of the currentfile(the current
file No. is showed on the main interface), and the time isaccurate to 1ms.
Clear all count: To clear the running times of every file in thememory
Delete all file: To delete all memory files
Format speedily: To format memory speedily, and then all thefiles in memory
will be deleted.
Format drastically: To format memory drastically, and then allthe files in
memory will be deleted.
Total: the total running times of all the files.
2). U-Disk File
If the “U-disk” entry in figure 8.4-1 is pressed, the systemwill show as figure 8.4-3,
and the operation method is all the same as figure 8.4-1.
01
02
03
File:
Delete
Copy to memery
Read udisk
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
55
Read Udisk: read the file list in the Udisk;
Copy to memory: copy the target Udisk file to the memory;
Delete: delete the selected Udisk file;
This system supports such file formats of Udisk as FAT32 andFAT16,
but it can identify them when the files are put under the rootdirectory of
Udisk. The file name of more than 8 characters willautomatically be cut
out by the system. The file name that has only English lettersand digits
will not show when they are copied to the mainboard. The filescopied
from the mainboard to Udisk will be placed under the rootdirectory of
Udisk.
4.6.21 Alarm Information of Display
When users are operating the system, or when the machine isrunning, some alarm
information such as water protecting error maybe shows asbelow:
Water error
Esc Enter
Push “Enter” key or “Esc” key, the system will execute somerelative steps.
Prompt
THUNDER LASER NOVA-35
www.thunderlaser.com DONGGUAN THUNDER LASER EQUIPMENTCO.,LTD
[emailprotected] No.197, Hudong Road, Shatian Town,
Tel :(86)769 826653 Dongguan, Guangdong, China
FAQs
What is the lifespan of the Thunder Laser? ›
Only our Nova series machines require a water chiller. How long does the laser tube last? Glass laser tubes on our Nova machines will last between 2500 and 4000 working hours, typically 2-4 years, depending on usage. The cost to replace them ranges from $450 (60w) to $1300 (130w).
What can a thunder laser cut? ›- Wood.
- Acrylic.
- ABS.
- Cork.
- Plastic.
- Paper.
- Glass.
- Leather.
Our Nova 35 laser cutting machine come in multiple sizes and feature an adjustable bed. The Nova series is renowned for its exceptional engraving quality with high resolution, thanks to the inclusion of hybrid servo motors in our laser cutting machine.
How fast does Thunder laser cut? ›One of the best functions of Thunder Lasers is their sleek speed. In just one minute, a standard laser cutter can cut about 8 meters of material — a 1,000 watt machine can even reach rates of 17 meters per minute.
Can a Thunder Laser engrave a gun? ›Material Application. > Can Thunder laser engrave on metal? “Co2 lasers like Bolt, Odin, and Nova can't cut or engrave into metal directly. However, you can leave a permanent mark on them using something like Cermark.
Does Thunder Laser have a camera? ›The ThunderCAM kits come with an OEM LightBurn camera, a Thunder Blue OEM LightBurn mount, a USB cable, a USB adapter, and a few wire management bits.
What is the most powerful laser I can buy? ›Class 4 lasers, the highest class and therefore the strongest laser you can legally own, produce 500 mW of power – or more – there is no legal maximum on milliwatts for class 4 – and is considered hazardous for users outside of an industrial setting.
What can you make with a thunder laser? ›Wood, plastic, leather, glass—our laser cutting machines for crafts can handle it all. From wood carvings to glass engravings, the possibilities are endless. With Thunder Laser, the only limit is your imagination.
What is the most powerful laser used? ›National Ignition Facility has the highest power laser. On July 5, 2012, NIF made history when its 192 beams delivered more than 500 trillion watts of peak power and 1.85 megajoules of ultraviolet laser light to its target.
Can you cut metal with a Thunder laser? ›You Can Mark Metal Using One of Our Laser Cutters
Although you can't cut metal using one of the machines from Thunder Laser USA, you can mark it.
What temperature does the Thunder laser work at? ›
Ideally you should operate your machine is a space that is between 60 and 80F, that is dust free with adequate ventilation and non condensing humidity. The machine can operate outside those bounds, even from 20-100F environments but the proper precautions should be taken to handle the extreme temperatures.
Does Thunder laser have a pass through? ›All Thunder laser cutters has a pass through door design to deal with such case, you can learn how to use this function easily from this video.
Do lasers have a lifespan? ›Typical lifetime of laser diode modules are 25,000 to 50,000 hours. If the laser diode temperature rises beyond the maximum operating temperature the long-term performance may degrade significantly, up to and including complete failure.
What is the life expectancy of a CO2 laser? ›With a brand like Reci, you can typically expect the laser tube to last up to 10,000 hours with proper care and maintenance.
What is the lifespan of the boss laser tube? ›Boss 65W CO2 Laser Tube 5,000 Hour Life.
Do fiber lasers lose power over time? ›While all lasers experience some level of power degradation, fiber lasers are known for their stable performance over an extended period. The specific power loss over time can vary depending on several factors, including the quality of the laser source, maintenance practices, and operating conditions.